diff --git a/include/configs/XPEDITE1000.h b/include/configs/XPEDITE1000.h
new file mode 100644
index 0000000..658e947
--- /dev/null
+++ b/include/configs/XPEDITE1000.h
@@ -0,0 +1,356 @@
+/*
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * config for XPedite1000 from XES Inc.
+ * Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com>
+ * (C) Copyright 2003 Sandburst Corporation
+ * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_XPEDITE1000	1
+#define CONFIG_SYS_BOARD_NAME	"XPedite1000"
+#define CONFIG_4xx		1		/* ... PPC4xx family */
+#define CONFIG_440		1
+#define CONFIG_440GX		1		/* 440 GX */
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_pre_init	*/
+#define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll */
+
+/*
+ * DDR config
+ */
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for setup */
+#define SPD_EEPROM_ADDRESS	{0x54}	/* SPD i2c spd addresses */
+#define CONFIG_VERY_BIG_RAM	1
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xff000000	/* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE		TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory */
+#define CONFIG_SYS_PERIPHERAL_BASE	0xe0000000	/* internal peripherals */
+#define CONFIG_SYS_ISRAM_BASE		0xc0000000	/* internal SRAM */
+#define CONFIG_SYS_PCI_BASE		0xd0000000	/* internal PCI regs */
+#define CONFIG_SYS_NVRAM_BASE_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
+#define CONFIG_SYS_GPIO_BASE		(CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x0400000
+#define CONFIG_SYS_MEMTEST_END		0x0C00000
+
+/* POST support */
+#define CONFIG_POST		(CONFIG_SYS_POST_RTC	| \
+				 CONFIG_SYS_POST_I2C)
+
+/*
+ * LED support
+ */
+#define USR_LED0	0x00000080
+#define USR_LED1	0x00000100
+#define USR_LED2	0x00000200
+#define USR_LED3	0x00000400
+
+#ifndef __ASSEMBLY__
+extern unsigned long in32(unsigned int);
+extern void out32(unsigned int, unsigned long);
+
+#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
+#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
+#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
+#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))
+
+#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
+#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
+#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
+#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
+#endif
+
+/*
+ * Use internal SRAM for initial stack
+ */
+#define CONFIG_SYS_TEMP_STACK_OCM	1
+#define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_ISRAM_BASE	/* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END		0x2000	/* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR
+
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)	/* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	3
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 }
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST		/* MirrorBit flashes are optional */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms) */
+
+/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C			1	/* I2C with hardware support */
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7f
+#define CONFIG_I2C_MULTI_BUS
+
+/* I2C EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
+
+/* I2C RTC: STMicro M41T00 */
+#define CONFIG_RTC_M41T11		1
+#define CONFIG_SYS_I2C_RTC_ADDR		0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR	2000
+
+/*
+ * PCI
+ */
+/* General PCI */
+#define CONFIG_PCI				/* include pci support */
+#define CONFIG_PCI_PNP				/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW			/* show pci devices on startup */
+#define CONFIG_SYS_PCI_TARGBASE	0x80000000	/* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CONFIG_SYS_PCI_TARGET_INIT		/* let board init pci target */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014	/* IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
+#define CONFIG_SYS_PCI_FORCE_PCI_CONV		/* Force PCI Conventional Mode */
+
+/*
+ * Networking options
+ */
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_NET_MULTI	1
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_PHY_RESET	1	/* reset phy upon startup */
+#define CONFIG_SYS_RX_ETH_BUFFER 32	/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_ETHPRIME		"ppc_4xx_eth2"
+#define CONFIG_PHY_ADDR		4	/* PHY address phy0 not populated */
+#define CONFIG_PHY2_ADDR	4	/* PHY address phy2 */
+#define CONFIG_HAS_ETH2		1	/* add support for "eth2addr" */
+#define CONFIG_PHY3_ADDR	8	/* PHY address phy3 */
+#define CONFIG_HAS_ETH3		1	/* add support for "eth3addr" */
+
+/* BOOTP options */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command configuration
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SNTP
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING	1		/* Command-line editing */
+#define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG			/* do not reset board on panic */
+#define CONFIG_PREBOOT				/* enable preboot variable */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1
+#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
+#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE		0x8000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff	U-Boot (512 KB)
+ * fff40000 - fff7ffff	U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff	FDT (256KB)
+ * ffc00000 - ffefffff	OS image (3MB)
+ * ff000000 - ffbfffff	OS Use/Filesystem (12MB)
+ */
+
+#define CONFIG_UBOOT_ENV_ADDR	MK_STR(TEXT_BASE)
+#define CONFIG_FDT_ENV_ADDR	MK_STR(0xfff00000)
+#define CONFIG_OS_ENV_ADDR	MK_STR(0xffc00000)
+
+#define CONFIG_PROG_UBOOT						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_BOOT_OS_NET						\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"if test -n $fdtaddr; then "				\
+			"$download_cmd $fdtaddr $fdtfile; "		\
+			"if test $? -eq 0; then "			\
+				"bootm $osaddr - $fdtaddr; "		\
+			"else; "					\
+				"echo FDT DOWNLOAD FAILED; "		\
+			"fi; "						\
+		"else; "						\
+			"bootm $osaddr; "				\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; "		\
+		"cmp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT							\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"autoload=yes\0"						\
+	"download_cmd=tftp\0"						\
+	"console_args=console=ttyS0,115200\0"				\
+	"root_args=root=/dev/nfs rw\0"					\
+	"misc_args=ip=on\0"						\
+	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+	"bootfile=/home/user/file\0"					\
+	"osfile=/home/user/uImage-XPedite1000\0"			\
+	"fdtfile=/home/user/xpedite1000.dtb\0"				\
+	"ubootfile=/home/user/u-boot.bin\0"				\
+	"fdtaddr=c00000\0"						\
+	"osaddr=0x1000000\0"						\
+	"loadaddr=0x1000000\0"						\
+	"prog_uboot="CONFIG_PROG_UBOOT"\0"				\
+	"prog_os="CONFIG_PROG_OS"\0"					\
+	"prog_fdt="CONFIG_PROG_FDT"\0"					\
+	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
+	"bootcmd_flash=run set_bootargs; "				\
+		"bootm "CONFIG_OS_ENV_ADDR" - "CONFIG_FDT_ENV_ADDR"\0"	\
+	"bootcmd=run bootcmd_flash\0"
+#endif	/* __CONFIG_H */